51.2V100Ah
Over 6000 cycles
01-LCD Screen
To display the information ofthe battery pack
02-Communication Port
CAN and RS485 communicationSuitable for wide inverter
03-ADS Switch
To setup battery addressfor identification
04-Capacity State
Four green LED lights to show the capacity status of battery pack
05/06-P+/P- Terminals
Connect to equipmentConnect in parallel to otherbattery pack for capacityexpanding
07-Circuit Breaker
Cut off the circuit automaticallywhen malfunctions occur
Parameters
| Rated energy(kWh) | 5.12KWh | Humidity(%) | 5~95% |
| Configuration | 2P16S | Altitude Limited(m) | 0-3000m |
| Nominal Voltage(V) | 51.2V | Weight(Kg) | 48Kg±3kg |
| Working Voltage(V) | 42V~58.4V | Dimension(mm) | 618×450×208.5mm |
| Nominal Capacity(Ah) | 100Ah | Storage temperature and humidity | -10℃~35℃（Within one month of storage） 25±2℃（Within three months of storage） 65%±20%RH |
Rated charge/discharge Current(A) | 50A/100A @25±2℃ | weight | 48kg±3kg |
| Maximum charging current | 100A@25±2℃ | cycle life | 6000 cycles @25℃ 50ACharge and discharge current 80%DOD |
| Maximum discharge current | 100A @25±2℃ | IP grade | IP20 |
| Working Temperature | 0～40℃(Charge) -20～40℃(Discharge) | Communication mode | CAN&RS485 |
For customized lithium battery specifications, please send requirements email to riley@ylkenergy.com. Our sales manager will contact you at the first time.
Inside module
Module is one of the secondary structures of power battery system. The module is mainly a combination that can supply power directly after the protection circuit board and shell are added to the single cell through series and parallel mode. It is an intermediate product between the single cell and pack.
-
Introduction
-This battery pack System, is applicable both for residential and commercial energy storage system, which is assembled with 3.2V 50Ah lithium iron phosphate cell in 16S2P configuration, And intelligent BMS form 51.2V 100Ah lithium battery system. Each pack support 16packs in parallel to easily expand capacity.
-Do not mix parallel the battery packs of different brands or models.
-
Functions
- Battery voltage calculation: 16 battery voltage sampling test,deviation ± 20mV.
- Battery and ambient temperature detection: 4 battery temperature sensors, 1 ambient temperature sensor, 1 MOS temperature sensor,deviation ± 2 ℃.
- Battery capacity and cycle times: complete a complete charging,discharging cycle to set the actual capacity. Monitor the remaining capacity of the battery with the capacity estimation accuracy within 5% deviation.
- In addition, the charging and discharging cycle time and the complete charging and discharging cycle time can be configured.
- Smart cell balance: charging and static balance strategies can be flexibly set to effectively extend the service life.
- Communication interface: PC or intelligent front-end can monitor battery data, control operation and set parameters through telemetry, remote signaling, remote adjustment, remote control and other commands. The communication protocol meets the requirements of YD/T 1363.3 and realizes cascade communication.
- Historical data recording, saving and reading: when the battery is abnormal, record and save real-time battery status and alarm information. At present, up to 500 historical fault data can be stored.
- Battery management system parameter setting: battery management system parameters, including cell battery over voltage/under voltage, battery total voltage over voltage/under voltage, charge and discharge over current, battery high/low temperature, battery capacity, working mode, charge and discharge limit current, can be set in the battery monitoring system.
- Working mode: charging and discharging current limiting, constant voltage output, direct output and other working modes can be set in the monitoring system.
- Multiple protection functions: hardware protection, battery protection, high and low temperature protection, output short circuit protection, etc.
Suggestions for using
the Products
- For UPS
- For Energy Storage System
A mains interruption may cause serious consequences. The uninterruptible power supply with battery module P-S 51.2V100Ah provides power even when the mains fails, protecting your system from power outages.
YP-S 51.2V100Ah ensures the efficient operation of the entire home system.In case of sudden suspension of household electricity consumption, with the home energy storage system, it can maintain continuity under such circumstances, and the response time is extremely short.
Application
Replacement SLA battery YX12V20Ah
View more >
Trolley Type Portable Power Station High-Power Mobile Power
View more >
